Cone crushers
Aftermarket manganese mantles and matching bowl liners or concaves for selected Metso Nordberg HP, GP and MP, and Sandvik CH and CS cone crushers. Chamber profile and material grade are confirmed against the supplied model, part number and operating duty.
View details
Cone crushers
Eccentric bushes, head bushes, socket liners, countershaft bushes, thrust washers and step plates for selected cone crusher models. Alloy, dimensions and running clearances are confirmed from part numbers, drawings or samples before manufacture.
View details
Cone crushers
Mechanical spares for selected crusher designs, including shafts, eccentric and drive components, and ring assemblies. Confirm the part number and required assembly scope.
View details
Jaw crushers
Fixed and swing jaw plates in selected tooth profiles for Metso C-Series and Sandvik CJ / QJ jaw crushers. Fitment is checked against the crusher model, part number and fixing dimensions supplied.
View details
Jaw crushers
Structural side plates and frame components reviewed against the machine drawing. The pictured side plate is not a cheek liner or toggle plate.
View detailsJaw crushers
Jaw stock and pitman assemblies, flywheels and bearing housings for major C-Series and CJ models, supplied either as bare castings or fully machined.
View details
Wear materials
Nominal manganese alloy families for application-specific review. Confirm chemistry, heat treatment and acceptance requirements for the quoted component.
View details
Wear materials
TiC reinforcement options can be reviewed for the specified liner and duty. Confirm the matrix, insert specification and evidence of performance before order. A visible reinforcement pattern alone does not establish its chemistry.
View details
Conveyor & roller
H-type, P-type and GH alloy cleaners, roller-brush, reversible, counterweight double-head and combined water cleaning systems. Primary and secondary configurations selected for belt speed, belt width, splice type, material and moisture conditions.
View details
Conveyor & roller
Impact bars support the belt through the loading zone. Bar layout, frame rating and access for replacement must be selected for the conveyor; slide-out or lowering sections depend on the quoted design.
View details
Conveyor & roller
Carrying, return, impact and training rollers, plus self-aligning idler assemblies selected to suit belt width, trough angle, load and operating environment.
View details
Conveyor & roller
Drive, tail, bend, snub and take-up pulleys with rubber or ceramic lagging. Existing drawings and key dimensions can be reviewed for replacement or refurbishment enquiries.
View details
Complete units
Multi-cylinder and single-cylinder cone crusher units can be quoted with selected spares and documentation. Configuration and support scope are confirmed per project.
View details
Complete units
Jaw crusher equipment for primary crushing applications. Confirm the feed, required throughput, drive, accessories and support included in the project quotation.
View details
Assurance
The quotation identifies the material, dimensional and inspection documentation included for the ordered part.
View detailsCross-reference
If your model is not listed, send it anyway — the table below is the common range, not the limit of what we can source.
Model names are identification references only. Exact part number, machine serial number and configuration must be checked before supply.
| Machine family | Models | Parts typically supplied |
|---|---|---|
| Metso Nordberg HP | HP100, HP200, HP300, HP400, HP500, HP700, HP800 | Mantle, bowl liner, torch ring, eccentric, bronze bushes, socket liner, main shaft |
| Metso Nordberg GP | GP100, GP200, GP300, GP500, GP550 | Mantle, bowl liner, main shaft, eccentric, countershaft, piston |
| Metso Nordberg MP | MP800, MP1000, MP1250 | Mantle, bowl liner, socket liner, eccentric, main shaft |
| Metso Symons | 3′, 4′, 4¼′, 5½′, 7′ | Bowl liner, mantle, socket liner, bronze components, gear set |
| Sandvik CH / CS | CH420, CH430, CH440, CH660, CH870 / CS420, CS430, CS440, CS660 | Mantle, concave, spider cap, arm guard, eccentric, bronze bushes |
| Sandvik H / S | H2800, H3800, H4800, H6800, H7800 / S2800, S3800, S6800 | Mantle, concave, dust seal ring, step plate, thrust washer |
| Metso C-Series jaw | C80, C96, C100, C106, C110, C120, C130, C140, C145, C160, C200 | Fixed jaw, swing jaw, cheek plate, toggle plate, seat, jaw stock |
| Sandvik CJ / QJ | CJ211, CJ409, CJ411, CJ412, CJ612, CJ615 / QJ241, QJ341 | Fixed jaw, swing jaw, cheek plate, toggle plate, tension rod |
Ordering
Provide these details so identification, availability and price can be reviewed.
Metso HP300, Sandvik CH430, Metso C140 — or the machine serial number.
The OEM reference is ideal. A photograph of the worn part works too.
If you have a preference or a site standard. Otherwise we will recommend one.
One-off, or the full set for a shutdown. Set pricing is usually better.
Send it all to chrisyumachineparts@gmail.com or call 0405 201 301.
Send the machine model and a part number, photo or drawing. We will confirm whether we can supply it, and what it will cost, after review of the supplied information.
